AES EL00PM-RAD Post Mount Vehicle Detector

Wireless Post-Mount Vehicle Detection for Gate Open Inputs

The AES EL00PM-RAD Post Mount Wireless Vehicle Detection System is an e-LOOP vehicle detector designed for gate and door access applications where a post-mounted detector is preferred over buried loop work. It detects the presence and movement of vehicles using a 3-axis magnetometer with radar confirmation, then sends a wireless signal to a nearby compatible transceiver.

This detector is used for entry, exit, presence, and parking-style vehicle detection depending on setup mode and site configuration. It is commonly used with automatic gate systems where the controller has a dedicated open input and auto-close enabled. Once the detector identifies a vehicle, the paired transceiver can trigger the gate or door controller input.

The EL00PM-RAD mounts to a post approximately 23.6 inches, or 600 mm, above ground. Its compact enclosure, IP68 ingress protection, 128-bit AES encrypted radio communication, and lithium battery operation make it suited for outdoor access control environments where trenching, saw-cutting, or permanent in-ground loop installation is not practical.

This device is for vehicle detection and access input control. It is not a monitored entrapment protection device and should not be used as a substitute for required gate safety devices.

Key Features

• Post-mounted wireless vehicle detection system
• AES model EL00PM-RAD
• Part of the AES e-LOOP vehicle detection family
• Uses 3-axis magnetometer vehicle detection
• Radar confirmation helps verify vehicle presence and movement
• Designed for gate and door controller open-input applications
• Supports exit/entry mode detection
• Supports presence mode detection
• Parking mode available through supported mode configuration
• Default EL00PM mode is exit mode
• Up to 3 m, approximately 9.8 ft., vehicle detection range
• Up to 50 m, approximately 164 ft., radio range
• 433.39 MHz wireless communication
• 128-bit AES encrypted radio security
• Auto-calibration support
• Magnet-based coding, calibration, mode change, and reset functions
• Up to 3-year battery life depending on daily activations and site conditions
• Powered by two 1.5V AA lithium batteries
• IP68-rated outdoor enclosure
• Rated for operation from -40°F to 176°F
• Quick post-mounted installation with no saw-cut loop required

Technical Specifications

• Manufacturer: AES Global
• Model / Part Number: EL00PM-RAD
• Product Type: Post-mounted wireless vehicle detector
• Series: AES e-LOOP Post Mount
• Detection Technology: 3-axis magnetometer with radar confirmation
• Sampling Rate: 8 Hz
• Detection Modes: Exit/entry mode, presence mode, and parking mode where supported
• Default Mode: Exit mode for EL00PM
• Detection Range: Up to 3 m, approximately 9.8 ft.
• Radar Read Distance Reference: Dead zone approximately 0.8 to 0.9 ft.; very high range approximately 3.2 ft.; high range approximately 6.5 ft.; maximum range approximately 9.8 ft.
• Radar Angle Reference: Approximately 60 degrees
• Radio Range: Up to 50 m, approximately 164 ft.
• Radio Frequency: 433.39 MHz
• Modulation: FSK
• Bitrate: 9.6 kbps
• Bandwidth: 250 kHz
• Antenna Type: PCB
• Nominal Output Power: 10 dBm
• Receive Sensitivity: -126.2 dBm
• Radio Security: 128-bit AES encryption
• Power Source: Two 1.5V AA lithium batteries
• Battery Life: Up to 3 years depending on daily activations
• Standby Power: 14 µA
• Activation Power: 35 mA
• Dimensions: 6.9 in. H x 2.7 in. W x 1.1 in. D
• Weight: 0.44 lb.
• Mounting Style: Post mounted
• Mounting Height: 23.6 in., 600 mm, above ground
• Mounting Hole Spacing Reference: Approximately 163 mm apart
• Ingress Protection: IP68
• Operating Temperature: -40°F to 176°F
• Calibration: Magnet-activated calibration with auto-calibration function
• Clearance During Calibration: Keep metal objects and vehicles clear of the detection area; manual references a 3.5 m clear radius
• Controller Requirement: Gate or door controller must have a dedicated open input and auto-close function enabled
• Required Receiver / Transceiver: Compatible AES e-LOOP transceiver required for wireless communication
• Compliance: Tested to CE approval
• Not Included: Gate operator, gate controller, monitored safety devices, mounting post, and external transceiver unless specifically included with the selected kit
• Installation Note: Do not mount near high-voltage cables because this can affect detection capability
• Application Note: For vehicle detection only; not a monitored gate safety or entrapment protection device

Conclusion

The AES EL00PM-RAD provides post-mounted wireless vehicle detection for gate and door access control applications that need a non-buried detector. Its magnetometer sensing, radar confirmation, encrypted wireless communication, IP68 housing, and battery-powered design make it useful for exit, presence, and access-trigger applications where the gate controller has a dedicated open input and auto-close enabled.